D SUB HD MA CRIMP SHELL 26P

D SUB HD MA CRIMP SHELL 26P

Part number: 09 56 200 5601

Description: D SUB HD MA CRIMP SHELL 26P

Application: Cable ConnectorD Sub High Density

Series: D-Sub High Density

No. of contacts: 26

Gender: male

Termination Type: Crimp


Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Crimping Tool - Basic Tool 09 99 000 0620 (2)

The basic tool
09 99 000 0620
Instruction Manual (2)

Safety ratchet
• The hand crimp tool can only be used after it has been
opened completely. Each crimp process has to be done fully, before the tool can be opened again. This guaranties a good quality crimp
each time.

Do not open or close the tool by force!

Early crimp unclamp
It is possible to open the tool during crimping if
necessary:
• Slightly hold together the grips of the tool
• Open the safety barrier on the rear side of the
tool by turning left or right
• Open the grips of the tool to release the partially
crimped contact.

Crimp process
• Fold up locator
• Assemble the contact into the locator 1 –
select the right chamber!
• Fold back the locator
• Close the tool until the contact will be hold– 2
• Put the wire into the crimp opening
• Crimp the contact until the tool can be released
• Take out the crimped contact.

Maintenance
Remove any existing material and dirt and clean the
crimp zone regularly. Check the crimp zone of the
tool for correct closing, clean all moving parts.
These should move smoothly in operation and lubricate them. (Use: machine oil
SAE 20).

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Crimping Tool - Basic Tool 09 99 000 0620 (1)

Harting Crimping Tool-Basic Tool 09 99 000 0620

The basic tool
09 99 000 0620
Instruction Manual (1)


It can be used with the following crimping insert sets

Marking of the FC-contacts is stamped on their rear site.
Locators are supplied with the crimping sets.
To order them separately use the following part-no.

Set up Crimping inserts

Set up Crimping inserts
• Screw-off the fixing screw (1) – pliers closed
• Close tool until it releases (open now the tool)
• Remove inserts (first upper part)
• Install new inserts – marking (2) has to have same colour
– first insert lower part
• Fix the screws again with: ISKA M4x18 (upper)
ISKA M4x9 (lower)
• Plug the locator from the top in a 90° position as shown in the picture



Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Crimp Tool 09 99 000 0501 Instruction Manual (3)

Harting Crimp Positioner Tool Maintenance

There is virtually no maintenance required.
Please keep the indenter free of debris and
dust. Please take care about:

• don’t immerse tool for cleaning
• don’t use oil for lubricating
• don’t disassemble the tool

Tool is for crimping purpose only!
Use with HARTING crimp contacts only!
Protect tool against high humidity and dust!
Don’t open under force!


Harting Crimp positioning tool 09 99 000 0501 Instruction Manual (3)

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Crimp Tool 09 99 000 0501 Instruction Manual (2)

Crimping Positioner Tool Instruction

Harting Crimp tool 09 99 000 0501

1. Insert contact and prepared wire into
indenter opening from side opposite
the positionier.
2. Squeeze handles together until ratchet
releases. Handle will return to the
open position. Remove crimped
contact and wire.









Harting Crimp positioning tool 09 99 000 0501 Instruction Manual (2)

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Crimp Tool 09 99 000 0501 Instruction Manual (1)

Instruction Manual for Crimp positioner tool 09 99 000 0501

General Information

Harting Crimp tool 09 99 000 0501

The tool has a double action ratchet. Nose
that the tool cannot be opened without
completing the cycle.
Preparation
1. Tool must be in open position.
2. Remove safety clip from positioner
guide.
3. Select positionier for contact to be
crimped.
4. Insert positionier into positioner guide
and turn 90 degrees until bayonet pins
lock.
5. Install safety clip into positioner guide
(optional).
6. Wire size and corresponding selector
number are shown on data plate.
7. With tool still in open position, raise
and rotate selector knob until number
indicated on data plate for wire size to
be crimped is in line with Sel.no.arrow.
8. To remove positioner remove safety
clip and reverse procedure described
in step 4 (four) above.

Harting Crimp positioning tool 09 99 000 0501 Instruction Manual (1)

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Contact US - Harting German

HARTING
Holding:
HARTING KGaA,Marienwerderstraße 3

D - 32339 Espelkamp

Telephone: +49 5772 47-0
Fax: +49 5772 47-400
http://www.HARTING.com/

HARTING
Subsidiary - Sales for connector technology and systems engineering:

HARTING Deutschland GmbH & Co. KG,Postfach 2451

D - 32381 Minden

Telephone: +49 571 8896 - 0
Fax: +49 571 8896 - 990 604
http://www.HARTING-Deutschland.de

HARTING
Subsidiary - development and production for industrial connectors:

HARTING Electric GmbH & Co. KG,Wilhelm-Harting-Straße 1

D - 32339 Espelkamp

Telephone: +49 5772 47-97100
Fax: +49 5772 47-495
http://www.HARTING-Connectivity-Networks.com

HARTING
Subsidiary - development and production for electronic connectors:

HARTING Electronics GmbH & Co. KG,Marienwerderstraße 3

D - 32339 Espelkamp

Telephone: +49 5772 47-97200
Fax: +49 5772 47-777

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German

Harting Connector Manufacturer in German

The HARTING Technology Group

The HARTING Technology Group is skilled in the fields of electrical, electronic and optical connection, transmission and networking, as well as in manufacturing, mechatronics and software creation. The Group uses these skills to develop customized solutions and products such as connectors for energy and data transmission applications including, for example, mechanical engineering, rail technology, wind energy plants, factory automation and the telecommunications sector.

HARTING also produces electromagnetic components for the automotive industry, and is a specialist in industrial applications in the form of enclosures, housings, cabling and/or the assembly of individual or complete systems, as well as automated vending systems.

Harting - Top Industrial Connectors Electronic Connectors Manufacturer in German